Plastic Junction Box — WAG Series (IP65 ABS/PC Screw-Cover)
IP65 plastic junction box with continuous gasket and stainless corner screws for reliable sealing.
ABS base + PC lid (clear or opaque): UV-stable, impact-resistant for indoor and sheltered outdoor use.
Molded bosses accept backplate / 35 mm DIN rail for neat mounting of terminals, PSUs, relays and I/O.
Pre-marked knockouts for cable glands (M16/M20/M25); blank unused entries to keep IP65.
Wide size family from compact sensor splices to larger control junctions.
Description
The WAG Series plastic junction box is a purpose-built enclosure for control wiring, sensor
splices, and small device integrations that must remain clean, dry, and easy to service. A rigid ABS base
delivers structural strength, while the polycarbonate (PC) lid (clear for instant visual checks or
opaque for light shielding) provides high impact resistance and UV stability. A continuous elastomer gasket works
with stainless steel corner screws to compress the seal evenly around the perimeter—achieving dependable
IP65 protection against dust and water jets in indoor and sheltered outdoor locations.
Inside, molded bosses accept an optional galvanized backplate or a 35 mm DIN rail,
so terminal blocks, miniature breakers, relays, and compact power supplies can be mounted neatly with repeatable
spacing. Clearly marked knockouts support common cable glands (M16/M20/M25); fit the correct gland
size and blank any unused openings to preserve the enclosure rating. With a flat rear surface, rounded edges, and
generous screw landings, WAG installs quickly on panels, walls, or machinery skids and remains serviceable over time.
Key Benefits
- IP65 environmental protection with a one-piece gasket and stainless fasteners.
- ABS/PC construction balances strength, weight, and UV/impact resistance.
- Clear or opaque lid options suit visual inspection or light-sensitive electronics.
- Backplate/DIN-rail ready interior for fast, tidy device mounting.
- Pre-marked knockouts simplify entry planning and reduce installation time.
- Clean industrial design—flat back for flush mounting; rounded corners for safety.
Specifications
| Enclosure Type | WAG Series — IP65 plastic junction box with screw-fastened lid |
|---|---|
| Materials | Base: ABS · Lid: UV-stabilized PC (clear / opaque) · Screws: Stainless steel · Seal: Elastomer gasket |
| Ingress Protection | IP65 (dust-tight & water-jet resistant when properly sealed) |
| Impact / Flame | High-impact PC lid; glow-wire resistance up to 650 °C (model dependent) |
| Temperature Range | Typical −25 °C to +100 °C (enclosure only; device limits may differ) |
| Mounting | Wall / surface mount; internal bosses for 35 mm DIN rail or galvanized backplate |
| Cable Entries | Side-wall knockouts sized for common glands (M16, M20, M25). Use matching glands and blanks. |
| Lid Options | Clear (rapid visual inspection) or opaque (light shielding / appearance) |
| Finish / Color | Light gray ABS base; clear or gray-tinted PC lid |
| Compliance | CE, RoHS; IP per IEC 60529 (documentation available on request) |
Typical Size Options (Outer Dimensions)
| Model | L (mm) | W (mm) | H (mm) | Lid | Notes |
|---|---|---|---|---|---|
| WAG 65×50×55 | 65 | 50 | 55 | Clear / Opaque | Ultra-compact sensor splices |
| WAG 95×65×65 | 95 | 65 | 65 | Clear / Opaque | Small terminal block sets |
| WAG 110×80×70 | 110 | 80 | 70 | Clear / Opaque | 2–4 modules on DIN/backplate |
| WAG 125×125×75 | 125 | 125 | 75 | Clear / Opaque | Square footprint for tight spaces |
| WAG 150×110×70 | 150 | 110 | 70 | Clear / Opaque | Popular control junction size |
| WAG 175×125×75 | 175 | 125 | 75 | Clear / Opaque | Extra wiring room |
| WAG 200×150×75 | 200 | 150 | 75 | Clear / Opaque | IO/relay clusters |
| WAG 260×200×90 | 260 | 200 | 90 | Clear / Opaque | Small assemblies / PSUs |
| WAG 300×220×130 | 300 | 220 | 130 | Clear / Opaque | Room for breakers + terminals |
| WAG 380×260×150 | 380 | 260 | 150 | Clear / Opaque | Multi-device projects |
The list above shows common sizes; additional dimensions and depths are available on request.
Accessories
- Galvanized backplate (pre-drilled or blank)
- 35 mm DIN rail with screws and spacers
- Cable glands & blanks (M16/M20/M25) to maintain IP65
- Label/marker set and mounting hardware kits
Applications
- Building automation and HVAC junctions (sensors, valves, actuators)
- Lighting and signage splices; façade and rooftop control points (sheltered)
- OEM machinery nodes, small power distribution tap-offs, I/O concentration
- Water-treatment, pump rooms, plant utilities, test fixtures
Installation Best Practices
- Mount vertically and use all fixing points; support cables to minimize strain on glands.
- Open only the required knockouts; select the correct gland thread/diameter and tighten to spec.
- After wiring, evenly tighten the stainless screws to compress the gasket—do not over-torque.
- Use clear lids for visual status; choose opaque lids to shield light-sensitive electronics.
- Record gland sizes, tightening torques, and circuit labels in your job sheet for maintenance.
Customization & OEM
- Custom size mixes, color/finish, printing/laser marking
- Factory machining of entries and mounting patterns
- Pre-installed DIN/backplate, terminals, glands, and labeling
- Documentation packs (CE/RoHS, IP statement) for your project file
